Roll-Out Mold Racks for Steel Dies Installed at Chinh Dat Company

Roll-Out Mold Racks for Steel Dies at Chinh Dat Company – Pull Out the Drawer, Lift Out the Mold

Long Quyen manufactured and installed a roll-out mold rack system for steel dies at Chinh Dat Company’s factory. Each drawer runs on wheeled rails with stop pins, so molds and heavy machinery can be stored on several levels yet still retrieved easily.

1,000–3,000 kgLoad per drawer
4–8Number of roll-out drawers
30+Years of Long Quyen experience
Project overview

Chinh Dat Roll-Out Mold Rack Project Overview

The roll-out mold rack system was installed directly on the factory floor to store steel dies and bulky machinery.

🏭

Customer

Chinh Dat Company – a mechanical engineering workshop using many steel dies and heavy equipment.

📦

Scope

Drawer-type roll-out mold racks dedicated to steel dies.

⚙️

Requirements

Store heavy molds on several levels, with fast and safe mold retrieval.

🧰

Long Quyen’s role

Configuration advice, manufacturing under an ISO 9001 quality management system, transport and installation at the customer’s factory.

The customer’s problem

The Factory Problem Before the Roll-Out Racks

Steel dies are heavy and hard to move – without a purpose-built structure, the mold store is always cramped and hard to control.

🧱

Molds stacked on the floor

Reaching a mold at the bottom meant lifting off everything above with a crane – slow and prone to collisions.

📉

Wasted storage space

Only one layer could be stored on the floor, leaving the factory height almost unused.

🛠️

Bulky machinery hard to organize

Besides molds, large equipment and jigs had no fixed place and were scattered around the workshop.

⚠️

Unsafe handling

Sliding heavy molds across the floor without guide rails or stop pins put workers at risk.

Technical specifications

Long Quyen Roll-Out Rack Specifications

Standard specifications of the roll-out rack range manufactured by Long Quyen.

Load capacity Typically 1,000–3,000 kg per drawer
Dimensions Rack heights of 1,500 mm, 1,700 mm, 1,900 mm or 2,100 mm
Levels 4–8 levels of roll-out drawers
Material 2 mm cold-rolled steel plate
Finish Painted or hot-dip galvanized; blue, white, green, orange-yellow or custom colors
Accessories Wheeled rails under the drawers, sliding trays and stop pins
Safety Stop pins hold the tray when pulled out; the structure allows handling aids to be added
Installation Knock-down structure that is easy to transport, assemble and adjust; manufactured to ISO 9001 and the 5S method

Loads and structure are calculated according to international practice for pallet racking systems.

Long Quyen’s solution

Long Quyen’s Solution

The mold rack configuration was chosen to suit Chinh Dat’s steel die sizes and factory height.

📏

The right height and number of levels

From a height range of 1,500–2,100 mm and 4–8 levels, Long Quyen fixed a configuration that makes full use of the factory height.

🛤️

Drawers on wheeled rails

Side supports carry wheeled rails, so mold trays slide in and out easily and lock firmly with stop pins.

💎

2 mm cold-rolled steel, hot-dip galvanized

2 mm cold-rolled steel plate with a painted or hot-dip galvanized finish for long-term durability.

🏗️

Flexible knock-down structure

The rack consists of separate components that are easy to bring into the factory, quick to assemble and can be dismantled and moved when the store is rearranged.

Results

Results After Installing Roll-Out Mold Racks at Chinh Dat

The factory’s molds and machinery now have proper places, and the production area is far tidier.

📈

Up to 70% storage space saved

Storing molds on several levels instead of spreading them on the floor freed most of the area previously occupied.

⚡

Much faster mold retrieval

Simply pull out the sliding tray to reach the required mold, without removing the levels above.

🗃️

Bulky machinery stored too

Besides steel dies, the racks also take heavy equipment and even light goods, consolidated in one area.

🛡️

Safer handling

Guide rails and stop pins control tray movement, reducing risk when handling heavy molds.

Project photos

Photos of the Roll-Out Racks and Long Quyen Warehouse Racking

Photo album taken at Chinh Dat’s workshop: rows of roll-out mold racks, pull-out trays with handles, powder-coated perforated upright frames and installation inside the working factory.

Overview of the roll-out mold racks for steel dies installed at Chinh Dat Company's factoryChinh Dat roll-out mold racks with steel trays pulled out on rails for crane liftingMulti-level roll-out mold rack with blue powder-coated steel trays at Chinh Dat's workshopLong Quyen installing roll-out mold racks for steel dies in Chinh Dat's operating factoryClose-up of the perforated uprights and diagonal bracing of the Chinh Dat roll-out mold rack during installationClose-up of a roll-out tray with handle on the mold rack at Chinh Dat CompanyDetail of the pull-out tray and powder-coated frame of the roll-out mold rack at Chinh Dat's workshop
About us

Why Choose Long Quyen?

A factory with nearly 30 years

We manufacture directly at our Xuan Phuong factory in Hanoi – no middlemen, factory-direct prices.

Free 3D layout design

Warehouse survey, 3D drawings and load calculations free of charge before quoting.

Nationwide installation

A professional installation team delivering on schedule throughout Vietnam.

European standards

High-quality steel, powder coating and load testing to FEM/SEMA standards.

Long-term warranty

24–60 month warranty (depending on rack type and accessories), scheduled maintenance and fast replacement parts.

Trusted by 500+ businesses

Partner to leading logistics, manufacturing and distribution companies in Vietnam.

GET FREE ADVICE →

Process

Project Delivery Process

1

Contact

Needs assessment and initial advice

2

Survey

Free on-site warehouse measurement

3

Design

3D layout drawing + quotation

4

Manufacturing

Fabrication at our Hanoi factory

5

Installation

Installation, load acceptance testing

6

Warranty

Long-term scheduled maintenance

FAQ

Frequently Asked Questions About Roll-Out Mold Racks

How many kilograms can each roll-out drawer carry?
Long Quyen’s roll-out racks typically carry 1,000–3,000 kg per drawer, enough for most steel dies. For especially heavy molds, the frame and rail sections are recalculated to actual requirements.
How many levels does a mold rack have, and how tall is it?
The standard configuration has 4–8 drawer levels, with rack heights of 1,500 mm, 1,700 mm, 1,900 mm or 2,100 mm. The height depends on the factory ceiling and the lifting equipment in use.
What are roll-out racks made of?
The racks use 2 mm cold-rolled steel plate with a painted or hot-dip galvanized finish. Standard colors are blue, white, green and orange-yellow, and they can be painted in your corporate colors.
Can mold racks be dismantled and relocated?
Yes. The knock-down structure of separate components is easy to transport, assemble and relocate when the factory layout changes – there is no need to scrap the old racks.
Which industries are roll-out racks suitable for?
They are widely used in mechanical engineering and automotive assembly, where mold volumes are large. Besides molds, the racks also store bulky machinery and even light goods.

Optimize Your Warehouse – Boost Efficiency – Cut Costs

Contact us now for a free survey and 3D layout design.

CALL NOW: 0903 422 179

Quick quote

Request a Quote for Roll-Out Mold Racks

Fill in your details and Long Quyen will reply within 30 minutes (business hours).